SIERRA 780S SERIES FLAT-TRACK

You must use a certified digital voltmeter to adjust zero and span as the voltmeter acts as a standard. Verify the flow meter is installed with the correct number of upstream pipe diameters as shown on page Sierra has a tradition of innovation spanning over 40 years and this spirit of innovation continues to drive our engineers each day! Vortex flow meters continue to be the industry standard for accurate steam flow measurement. Use the first option with a separate power supply if a specific voltage is needed for the alarm output. Pay very close attention to all warnings that apply to your application. Back to home page. All fingers point at you if productivity slips because of incorrect steam flow calculation.

Multivariable for five 5 measurements in one compact device. For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees. Kam Bansal, the Director of Engineering, has some useful tips for successful vortex installations and common mistakes to The location meets the required minimum number of pipe diameters upstream and downstream of the sensor head see Table Printed circuit boards are sensitive to electrostatic discharge. Sierra was awarded an honorable mention. Other product and company names listed in this manual are trademarks or trade names of their respective manufacturers.

FlatTrack S UHP – FLOWMETH

Sales tax may apply when shipping to: K-Factor Correction Change the calibration correction factor to compensate for flow profile disturbances or specific application conditions.

China Pattern Approval Certificate. Your flow meter will continue to indicate flow and generate a signal if the flow is over the maximum range, but will not operate within the specified accuracy. To use an external power supply for an isolated alarm output, connect as shown in Figure or Figure weries For all installations not using solid metal conduit, the ferrite clamp must be installed just above the input power wire entry into the enclosure Figure When data collection is complete, siierra off power to the flow meter.

When Sierra-Asia was founded in China inwe were small but motivated. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.

  CALOREX VARIHEAT SERIES 3

Line pressure and temperature will not exceed the flow meter rating. You cannot add or subtract sefies length without returning the meter to the factory for re-calibration. The location meets the required minimum number of pipe diameters upstream and downstream of the sensor head see Table Thermal flowmeter solutions for energy applications Sierra thermal flowmeters provide precise flow measurement solutions for a variety of industrial and energy-related applications such as flare gas measurement, cogeneration, biogas measurement, district energy applications, clean coal technology and many more.

Select the desired range. Get the item you ordered or get your money back.

Set the multimeter to read in the Ohm range. Disconnect the multimeter and replace the four-position jumper on the sensor terminals. Add to watch list. The Series S meter solves the problems associated with monitoring flow in installations where long runs of straight pipe are not available. InnovaMass Training Video 1 – Introduction: Most facilities managers are in the hot seat to account for all of the flow energy, going in and out of their facility which is no easy task.

To rotate the display board: Flow Measurement instrumentation for maximize steam flow meter productivity We get it. Sierra thermal flowmeters provide precise flow measurement solutions for a variety of industrial and energy-related applications such as flare gas measurement, cogeneration, biogas measurement, district energy applications, clean coal technology and many more.

Rload is the total resistance in the loop, including the wiring resistance. Use the first option with a separate power supply if a specific voltage is needed for the alarm output. Also, verify the meter is located where the gas is clean and dry and the meter is calibrated for the gas to be measured. We recommend recording the current values before making any changes to the current zero or span settings. The terminal designations are labeled inside the enclosure cover.

If needed, adjust the optional display to the desired orientation, as follows. Failure to do so could result in injury or death. How a Power Plant Works When most people think of power plants, they immediately jump to an image of All AC power connections must be in accordance with published CE directives.

  WATERWORKS CINEMA SHOWTIMES

Flowmeter SmartTrakĀ® 100 Series

Remove the four-position jumper from Flat-frack, J6, J7 and J8 see below for location. You are responsible for determining if this mass flow meter is appropriate for your oxygen application.

Skip to main content. Sieerra Bansal, the Director of Engineering, has some useful tips for successful vortex installations and common mistakes to Also, before installation check your flow system for anomalies such as: Flat-trck pressure should not vary more than 50 psi 3. Check the flow meter wiring for correct connections as described in Chapter 2. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.

For an internally powered, non-isolated mA output, connect as shown in Figure or Figure To make changes, at the password prompt use the UP arrow until the number 11 is displayed.

To use the mA isolated output, an external 12 to 36 VDC power supply is required. Pay very close attention to all warnings that apply to your application.

Inline Thermal Mass Flow Meter | Sierra Instruments | FlatTrak S | Procon

You must use a certified digital voltmeter to adjust zero and span as the voltmeter acts as a standard. Series S Flow Sensing Principle Interest will be charged to your account from the purchase date if the balance is not paid in full within 6 months.

Part of Sierra’s Big-3 iSeries family of flow meter technologies. Adjust the voltage to 2. Every flow meter is only as good as its calibration.

After verifying the factors above, follow the troubleshooting procedures outlined on the next page.